Přihlásit
 
HlavníKnihovnaCertifikaceDownloadPodporaKomunitaFóra
Zdroje informací pro profesionály v oboru IT >
> 
> 
Help trying to get FIM 2010 DL management to work

一般討論 Help trying to get FIM 2010 DL management to work

  • 29. února 2012 14:36
     
     
    Přihlásit se a hlasovat
    0

    Hello,

    I am trying to get a basic demo of FIM doing Exchange self service DL management working and it's just not playing.

    I have built the servers as per the FIM instructions below, I have the FIM portal all working and can go in and now create a DL, but whilst it does say the DL has been completed groups are not getting created in AD, nor being stamped by Exchange (FIM has E2010 tools installed)

    I have the FIMMA and the ADMA in and the only error I am getting going through the sync is during the FIMMA export where I get this below:

    Is it this process when you export from FIM it then goes to create the group in AD and then then mail-enabled the object in Exchange?

    IS

    http://technet.microsoft.com/en-us/library/ee534915(v=ws.10).aspx

     

Všechny reakce

  • 29. února 2012 16:39
     
     
    Přihlásit se a hlasovat
    0

    Confirm you have the Sync Rule, the group object has the ERE and the Enable Provision from Sync is enabled in Tools, Options. 

    Your screen shot was of a Export to the FIM MA.  A view of a Sync from the FIM MA would be better.  Also, an export on the AD MA. 

    Eric

    Eric

     
  • 1. března 2012 10:36
     
     
    Přihlásit se a hlasovat
    0

    Hi Eric,

    Thanks,

    I only have inbound sync rule from AD in FIM Portal, there's nothing in the instructions about creating an export to AD? Here are some more screenshots though, but I do have the Enable Provision Sync in Tools/Options.

     
  • 1. března 2012 11:01
     
     
    Přihlásit se a hlasovat
    0

    Can someone confirm that the instructions here: http://technet.microsoft.com/en-us/library/ee534915(v=ws.10).aspx are sufficient to set-up a self service DL management demo?

    It appears to be missing these export steps back to AD?

     
  • 1. března 2012 11:21
     
     
    Přihlásit se a hlasovat
    0

    Hello,

    You don't seem to have any exports to ADDS in your run profiles, as you noticed yourself.

    Please follow the instructions found here to find out how to provision and synchronize the information back to ADDS http://technet.microsoft.com/en-us/library/ff686261(v=ws.10).aspx .


     
  • 1. března 2012 11:27
     
     
    Přihlásit se a hlasovat
    0

    Thanks, I'm really surprised that this is not in the actual Technet article on how to do this.

    That link appears to be just for security groups, are there additional steps specifically relating to Distribution Lists?

    • Upravený SixFooter 1. března 2012 11:29
    •  
     
  • 1. března 2012 13:26
    Vlastník
     
     
    Přihlásit se a hlasovat
    0

    A security group is a "distribution list + SID".
    There are no steps that are distribution list specific.

    Cheers,
    Markus

    Markus Vilcinskas, Knowledge Engineer, Microsoft Corporation

     
  • 1. března 2012 13:32
    Vlastník
     
     
    Přihlásit se a hlasovat
    0

    Regarding your error, have you looked at this article yet?

    Cheers,
    Markus

    Markus Vilcinskas, Knowledge Engineer, Microsoft Corporation

     
  • 1. března 2012 15:19
     
     
    Přihlásit se a hlasovat
    0
    Thanks Markus. I was thinking there needs to be a step/config that tells FIM to run the Exchange tools to mail-enable the group? Which accounts need which permissions etc..
     
  • 1. března 2012 15:20
     
     
    Přihlásit se a hlasovat
    0
    No, thanks! Will look now.
     
  • 5. března 2012 10:11
     
     
    Přihlásit se a hlasovat
    0

    Right, following the above article I can now get FIM provisioning DL's to AD/Exchange. You do need to add the mailnickname as an additional attribute otherwise the update-recipient command wont work, but at least we're almost there.

    I now have 2 new issues:

    1.) FIM isn't adding anyone to the DL. Do I need to have inbound sync rule for FIM to be able to do this?

    2.) I get the following error when attempting to modify/delete the objects? failed-creation-via-web-services/MembershipLocked/An attribute is required to complete the operation.<


    • Upravený SixFooter 5. března 2012 17:39 cleaned up
    •  
     
  • 6. března 2012 11:56
     
     
    Přihlásit se a hlasovat
    0

    FIM is driving me nuts!

    Why can't there be a simple how to guide to get self service DL's working, you have to piece together 3 or 4 articles, all with some form typo or error with the end result that nothing works :(

    For something that is such a big selling point for FIM, a simple step by step procedure would surely be warranted? Has anybody seen one, I'd even buy it!

    This article purports to be a design and deployment guide, but really..honestly isn't: http://technet.microsoft.com/en-us/library/ff645313(WS.10).aspx