Wi-Fi Issues in Windows 7 build 7100(RC) here.
I am having issues with my network connection on my Windows 7 build 7100. I get a "Limited Connectivity" and "No internet access"while in fact they should be available. My router is being detected on my laptop but does not connect to the internet.So, I thought i'd put up all I've done with experimenting up here, so that MS can fix it quickly. Here's my system Configuration:
Acer Aspire Notebook 4520
AMD Athlon 64 x2(2.0 Ghz, 2*256KB L2 cache)
Nvidia Geforce 7000M.
2Gib DDR 2.
Broadcom 802.11 b/g wireless adapter with Nvidia nForce networking controller.
Windows 7 build 7100(Public RC).
UTStarcom Wirelesss router model WA3002G4 (This is my Access Point).
Symptoms:
1. After system boots, wireless connectivity works flawlessly. But the working state only lasts for what appears to be a random interval of time(sometimes a minute or two, at other times in excess of 30 minutes).
2.The system then loses INTERNET connectivity. The taskbar icon shows an '!' mark and reports "Limited Connectivity".The system still continues to detect the wireless router however!
3.Restarting the system causes an unusually lengthy shoutdown(4-5 minutes sometimes!).
4.However, after restart, wireless connectivity is completely restored. Note that, the router(UTStarcom) has remained on throughout the process.
5.Resetting the router(UTStarcom) while the system remained ON does not cure the problem.
6.When switching to ethernet AFTER the problem has occured (with WiFi)( i.e Wifi adapter on the laptop disabled(via a switch on the laptop),and the ethernet chord plugged in later), the icon on the taskbar continues to show "Limited Connectivity" and "No internet access". However, I CAN connect to the internet through IE8 or Firefox.
7. The problem DID NOT EXIST in Windows 7 build 7000.
Troubleshooting steps adopted:
1. Typical troubleshooting was to try to disable the wireless card and then re enable it using the Device Manager. However, Device Manager hangs after clicking on Disable.
2. Tried to randomize identifiers for ipV6 usingnetsh interface ipv6 set global randomizeidentifiers
Dos command. But, the problem persists. I have now reset the identifiers.
3.Tried to set the power options to "High Performance", hoping the problem was associated with power. But no dice there either.
4.Updated Windows 7 through Windows Update. The system is fully updated but the problem persists.
5.Installed the latest drivers from both Nvidia and Broadcom, to no avail.
Personal Conclusions:
Because I can still connect to the router(UTStarcom) with my DELL (Which has Windows Vista), and because the problem is only occuring since I installed the Windows 7 RC, I'm inclined to believe that the problem is with Windows. Further, my online exploits to solve this problem show that the Nvidia nForce networking controller appears common in most of the cases with this problem. Nevertheless, it is extremely puzzling why a build almost 3 months older than the RC, performed stably with wireless networking, while this one cant!Symptom 6, seems to lead to the fact that, perhaps, an internal Windows process seems to have "hung" (causing the system to fail to update the ethernet connection settings), which may the reason why the router is detected but still we have no internet access. I also remember to have read somewhere,someone saying that he noticed that when the problem occured, windows was not adhereing to the protocol's time-out periods.I also have suspisions on whether this could be related to faulty WEP encryption/decryption on Windows side.
- Edited byajay.ramesh Friday, May 08, 2009 5:13 AM
- Edited byajay.ramesh Friday, May 08, 2009 5:17 AM
All Replies
- I to am having the same problem except when i boot up internet works flawlessly, but when i close the lid and it goes to sleep, i will come back and open it up and it shows limited connection. I have to reboot after coming out of sleep if i want to use the internet. I would also like some help with this issue
- I'm having the same exact problem. I have two versions of Windows on my laptop. The Windows 7100 RC and the Windows 7000 Beta. The Beta (which I'm booted into now) operates flawlessly in terms of wireless. The RC boots up, works ok for a minute or two, then stops. Troubleshooting never works, disconnecting and reconnecting never works. Even plugging in an ethernet cable didn't work. Not sure what the problem is but it sucks because I upgraded the Vista side of the machine into RC1 because I loved the Beta so much.
- Read this
http://social.technet.microsoft.com/Forums/en-US/w7itpronetworking/thread/1b4d475d-f2e1-44f5-a96b-829b48b5e3de - thanks but i tried that already. doesn't work.
- Are you using Firefox web browser?
- On my test Windows 7 RC1 desktop at work I often get the "Limited Connectivity" warning, but as far as I can tell everything is working fine (I can browse the net fine using Firefox and I get no drops from applications that access systems over the local network). This is a hardwired connection and we don't do wireless. We use Cisco switches/routers. I assumed it has something to do with the way it "discovers" if you have internet access. I'm on a corporate network with over 5000 users that spans the entire state with multiple "main" offices around the state.
- I have the exact same problem. Mine is a Dell desktop with a Linksys wireless card.
Because of this problem I now have to reboot all the time. It's really frustrating.
This did not happen when the exact same hardware set up was running Vista. - I too am having this problem.(custom pc with linksys wifi card). Luckly I have a second hdd with xp still on. I have tried everything with win 7 even fresh install and still the same wifi problems. any suggestions
- I have a Linksys Wireless N and am having the exact same problem. I think it is associated with the drivers for x64 version as I am not having any problems at all with x32 on my laptop. I have the exact same symptoms and everything on my main PC which is running 64 bit. If MS could fix this glitch that would be awesome!!!
On my test Windows 7 RC1 desktop at work I often get the "Limited Connectivity" warning, but as far as I can tell everything is working fine (I can browse the net fine using Firefox and I get no drops from applications that access systems over the local network). This is a hardwired connection and we don't do wireless. We use Cisco switches/routers. I assumed it has something to do with the way it "discovers" if you have internet access. I'm on a corporate network with over 5000 users that spans the entire state with multiple "main" offices around the state.
with all due respect...since you're using a "wired" connection, and this is a thread about "wireless internet problems", your comment does nothing to help anyone.Are you using Firefox web browser?
it has nothing to do with the browser. the internet connection plain and simply does not work. I could be using Firefox, Internet Explorer, Chrome, Safari, ____ Netscape Navigator and it wouldn't workI have a Linksys Wireless N and am having the exact same problem. I think it is associated with the drivers for x64 version as I am not having any problems at all with x32 on my laptop. I have the exact same symptoms and everything on my main PC which is running 64 bit. If MS could fix this glitch that would be awesome!!!
I agree...i think it's a pretty silly oversite and a real slap in the face to people who did upgrades from Vista to 7... my laptop becomes practically useless if it can't wirelessly connect to the internet.- I have the same problem, but it appears to be related with the bittorrent client. I've tryed everything and stills happens when i start the utorrent, bittorrent, or bitcomet.
I to am having the same problem except when i boot up internet works flawlessly, but when i close the lid and it goes to sleep, i will come back and open it up and it shows limited connection. I have to reboot after coming out of sleep if i want to use the internet. I would also like some help with this issue
exactly the same issue as above on my Dell Inspiron 6400, else everything every software is smooth and fast.
it never happened on Vista- having same issue 32bit windows 7rc on a acer aspire 5100 when it wakes from sleep it starts getting limited connectivity, after a reboot system works correctly.
- I am having the same issue. Windows 7 build 7000 worked fine with all of my hardware and software. Upgraded to RC1 and now I am having this issue with my internet connection. While the connection seems to fail at random there is a sure fire way to make the connection fail. If left alone, my connection may stay up for 5 to 30 minutes. If I start to download a file the connection fails almost instantly. it is like the software (windows) cannot handle the larger amount of data being transfered. If anyone has any ideas I would love to hear then. Thanks.
- I have exactly the same issue issue, but after reinstalling drivers a couple of times and trying older ones i have it working now but strangly the activity light stays on all the time and does not flicker when in use. Also if I put the laptop (Acer 4520) to sleep I have to first turn off wifi with the manual switch and then it is able to wake up fine, if I dont do that it wakes up fine but then hangs the whole system after about 2 min.
- I have the same exact god dam stupid windows 7 RT problem. However I will take a rigged up fix for now until microsoft has the issue one day settled... I have an ACER 4520. was wondering which driver you installed to get the connectivity to stay. I will of course search myself however knowing the amount of junk out there i was hoping you could point me in the right direction and save myself from searching the entire haystack for the elusive needle. Thank-you.
- I am having a similar problem. I have a Thinkpad t60 with an intel pro 3945ABG mini-pci express adapter. I am running W7RC 64 bit. I noticed that when the computer goes to sleep or hibernates, it will have the limited connectivity problem upon wake up. Another strange thing I noticed is that it does receive an ip address and all of the other dhcp information, but instead of picking up the connection at 54mbps it shows up as 1mbps. When it is in this state, I cannot access the internet at all. Nothing seems to help except to turn of the router for 30 seconds or so and to reboot the computer. If you do just one of those you have the same problem. For me, it's just about definitely related to sleeping and not time as I can be connected all day as long as I don't put my computer to sleep.i don't have any torrents running on my computer, and all of my software is pretty vanilla. I hope it is just a driver issue, but is it likely since so many different adapters are having the same issue? Anyway, any help would be great. I like w7 a lot but this is just frustrating.
- HELLO there,
I was troubleshooting with something like you are complaining to.
And after i google it, i found something INTERESTING...
It Work for me, Try it... It is VERY SIMPLE, BUT I DONT KNOW WHY...
DISABLE ,,HOME GROUP" from Network and Sharing Center
Good Luck for all of you !!
BTW I have also an INSPIRON 6400 I am having a similar problem. I have a Thinkpad t60 with an intel pro 3945ABG mini-pci express adapter. I am running W7RC 64 bit. I noticed that when the computer goes to sleep or hibernates, it will have the limited connectivity problem upon wake up. Another strange thing I noticed is that it does receive an ip address and all of the other dhcp information, but instead of picking up the connection at 54mbps it shows up as 1mbps. When it is in this state, I cannot access the internet at all. Nothing seems to help except to turn of the router for 30 seconds or so and to reboot the computer. If you do just one of those you have the same problem. For me, it's just about definitely related to sleeping and not time as I can be connected all day as long as I don't put my computer to sleep.
HELLO there,i don't have any torrents running on my computer, and all of my software is pretty vanilla. I hope it is just a driver issue, but is it likely since so many different adapters are having the same issue? Anyway, any help would be great. I like w7 a lot but this is just frustrating.
I was troubleshooting with something like you are complaining to.
And after i google it, i found something INTERESTING...
It Work for me, Try it... It is VERY SIMPLE, BUT I DONT KNOW WHY...
DISABLE ,,HOME GROUP" from Network and Sharing Center
Good Luck for all of you !!I to am having the same problem except when i boot up internet works flawlessly, but when i close the lid and it goes to sleep, i will come back and open it up and it shows limited connection. I have to reboot after coming out of sleep if i want to use the internet. I would also like some help with this issue
exactly the same issue as above on my Dell Inspiron 6400, else everything every software is smooth and fast.
it never happened on Vista
HELLO there,
I was troubleshooting with something like you are complaining to.
And after i google it, i found something INTERESTING...
It Work for me, Try it... It is VERY SIMPLE, BUT I DONT KNOW WHY...
DISABLE ,,HOME GROUP" from Network and Sharing Center
Good Luck for all of you !!
BTW I have also an INSPIRON 6400
HELLO there,I am having issues with my network connection on my Windows 7 build 7100. I get a "Limited Connectivity" and "No internet access"while in fact they should be available. My router is being detected on my laptop but does not connect to the internet.So, I thought i'd put up all I've done with experimenting up here, so that MS can fix it quickly. Here's my system Configuration:
Acer Aspire Notebook 4520
AMD Athlon 64 x2(2.0 Ghz, 2*256KB L2 cache)
Nvidia Geforce 7000M.
2Gib DDR 2.
Broadcom 802.11 b/g wireless adapter with Nvidia nForce networking controller.
Windows 7 build 7100(Public RC).
UTStarcom Wirelesss router model WA3002G4 (This is my Access Point).
Symptoms:
1. After system boots, wireless connectivity works flawlessly. But the working state only lasts for what appears to be a random interval of time(sometimes a minute or two, at other times in excess of 30 minutes).
2.The system then loses INTERNET connectivity. The taskbar icon shows an '!' mark and reports "Limited Connectivity".The system still continues to detect the wireless router however!
3.Restarting the system causes an unusually lengthy shoutdown(4-5 minutes sometimes!).
4.However, after restart, wireless connectivity is completely restored. Note that, the router(UTStarcom) has remained on throughout the process.
5.Resetting the router(UTStarcom) while the system remained ON does not cure the problem.
6.When switching to ethernet AFTER the problem has occured (with WiFi)( i.e Wifi adapter on the laptop disabled(via a switch on the laptop),and the ethernet chord plugged in later), the icon on the taskbar continues to show "Limited Connectivity" and "No internet access". However, I CAN connect to the internet through IE8 or Firefox.
7. The problem DID NOT EXIST in Windows 7 build 7000.
Troubleshooting steps adopted:
1. Typical troubleshooting was to try to disable the wireless card and then re enable it using the Device Manager. However, Device Manager hangs after clicking on Disable.
2. Tried to randomize identifiers for ipV6 usingnetsh interface ipv6 set global randomizeidentifiers
Dos command. But, the problem persists. I have now reset the identifiers.
3.Tried to set the power options to "High Performance", hoping the problem was associated with power. But no dice there either.
4.Updated Windows 7 through Windows Update. The system is fully updated but the problem persists.
5.Installed the latest drivers from both Nvidia and Broadcom, to no avail.
Personal Conclusions:
Because I can still connect to the router(UTStarcom) with my DELL (Which has Windows Vista), and because the problem is only occuring since I installed the Windows 7 RC, I'm inclined to believe that the problem is with Windows. Further, my online exploits to solve this problem show that the Nvidia nForce networking controller appears common in most of the cases with this problem. Nevertheless, it is extremely puzzling why a build almost 3 months older than the RC, performed stably with wireless networking, while this one cant!Symptom 6, seems to lead to the fact that, perhaps, an internal Windows process seems to have "hung" (causing the system to fail to update the ethernet connection settings), which may the reason why the router is detected but still we have no internet access. I also remember to have read somewhere,someone saying that he noticed that when the problem occured, windows was not adhereing to the protocol's time-out periods.I also have suspisions on whether this could be related to faulty WEP encryption/decryption on Windows side.
I was troubleshooting with something like you are complaining to.
And after i google it, i found something INTERESTING...
It Work for me, Try it... It is VERY SIMPLE, BUT I DONT KNOW WHY...
DISABLE ,,HOME GROUP" from Network and Sharing Center
Good Luck for all of you !!- I tried your little disable home group! doesnt work... nothing works... Ive tried regedit... ive tried everything... I hope someone has informed Windows there is a major problem with this little WLAN and windows 7 RT... I hope its fixed soon i will check everyday for an update or drive update. However I am forced to restart my computer everytime... I might just jump ship and bite the bullet and go back to vista! I really dont want too.... HOW IS EVERYONE ELSE MAKING OUT?
- Any luck I have tried everything ever posted on a forum so far nothing had worked for me! how about you?
- nothing worked. I'm going to install vista again. I'm not going to buy another piece of *** software. I know is just a RC, but it never happen in the beta, so i don't know why it broke up after... What are they doing? vista 2?
- Same problem. regular internet browsing.. suddenly wireless stop. I am glad I had time to write this post. I never know how long time I am given on the net... Rebooting is the only remedy.. My machine is useless now.Acer TravelMate 5510
- HELLO! can any one from Microsoft hear us?
whats the use of this forum if MS tech guys cant respond on this simple problem.
going back to Vista soon if this problem is not sorted out soon. Same problem. regular internet browsing.. suddenly wireless stop. I am glad I had time to write this post. I never know how long time I am given on the net... Rebooting is the only remedy.. My machine is useless now.
Ok, so right after i posted this, I noticed that an update for my Broadcom 802.11g Network Adapter was ready for download and install at Windows Update. ofcourse my networked hanged, but i restarted, and did the update. And now everything seems to work just fine!!! great! 30min online, downloaded big files, no problem so far!Acer TravelMate 5510- how do you disable home group exactly?
- So i downloaded the new updates from windows and it seems to have worked for my wireless... I have to be honest... i tried everything right up until the point of reading movemats post... it has been on for a consistent 1h 57min.... GOOD LUCK BOYS I hope Im never back to the forums again... except to say i love this program except for this glitch...
- Running Windows 7 RC 7100 x64
My wireless adapter is the Rosewill RMX-N2X Wireless N USB.
Wireless worked flawlessly in Windows 7 7000 Beta.
Wireless works fine on my Windows 7 RC 7100 x86 on my netbook.
Ever since the I installed 7100 x64 on my home PC though, my wireless has been going dead. The link light dies, the status shows Limited Connectivity (No Internet), and anytime I try to access ANYTHING related to networking, it freezes up. I've even had one blue screen.
I've tried 4 different fresh installs, problem persists.
I've tried the disable IPv6, problem persists.
I've tried the turn off let Windows turn off device to save power option, problem persists.
The only way to temporarily restore wireless is a full power cycle, but the problem just comes back again anywhere from a half hour to 5 hours. how do you disable home group exactly?
folow this steps :
- Open Network and Sharing Center
- in the left panel chose HomeGroup from Down Left Side
- Then read and Disable this monster...
Good luck- i was unable to connect to a wireless router trough my msi wireless lan card. Even with the original driver the card doesn't install.
how do you disable home group exactly?
folow this steps :
- Open Network and Sharing Center
- in the left panel chose Home Group from Down Left Side
- Then read and Disable this monster...
Good luck
@catalinux
I have tried this by "leave HomeGroup" option there is no option "disable home group".
Can you please guide us step by step how can we do this. How to test it? does it need a restart? or what not?
thanks.how do you disable home group exactly?
folow this steps :
- Open Network and Sharing Center
- in the left panel chose Home Group from Down Left Side
- Then read and Disable this monster...
Good luck
@
I have tried this by "leave HomeGroup" option there is no option "disable home group".
Can you please guide us step by step how can we do this. How to test it? does it need a restart? or what not?
thanks.
Sory about missinformation There is no DISABLE word, the method is : LEAVE HomeGroup and after that is no need to restart your machine, this method aplies instantly... just try.. step back to the computer about lets say 5 to 30 minutes and you will see that problem no longer exist...- I hope this helps...1. click "start"2. click "control panel"3. click "network & internet"4. click "network sharing center"5. click "advanced sharing settings"6. click the "^" associated to "home or work"7. scroll to the bottom you will see "homegroup connections"8. click "use user accounts and passwords to connect to other programs"I hope this is the one. I used it and updated my windows and the problem seems to have disappeared...
I hope this helps...
1. click "start"2. click "control panel"3. click "network & internet"4. click "network sharing center"5. click "advanced sharing settings"6. click the "^" associated to "home or work"7. scroll to the bottom you will see "homegroup connections"8. click "use user accounts and passwords to connect to other programs"I hope this is the one. I used it and updated my windows and the problem seems to have disappeared...
Thanks so much for the step by step help, but "when i close the lid and it goes to sleep, i will come back and open it up and it shows limited connection ". This problem is not fixed :(- Ha. I messed around with stuff trying to fix the problem and now I can't hibernate either. The screen goes blank, but the hard drive light is lit up continually (all night yesterday!). All you can do is a hard power off and restart. W7 complains about it on reboot, and I still have the same network problems. Good grief. Is this a late april fool's joke or something?
- All of this sounds like driver problems. I have a ThinkPad T61 with absolutely no problems. The T61 has Intel 82566MM Gigabit wired connection, and Intel 4965AG WiFi.
However, I do NOT use sleep. Sleep causes more problems than it solves, IMO. Hibernation/resuming works fine, however. Using 64 bit RC.
Also 7 hibernates MUCH MUCH faster than Vista. Vista would take a minute or 2, 7 hibernates (even with more RAM!) in about 20 seconds. - Hi I am having the same issue. I have brand new HP laptop. I was not having connectivity issues until I downloanded the RC version of Windows 7. I allow others to use my wifi router and they have no issues. I get a message saying low connectivity or no connection at all. I use Windows 7 find fix and repair option and it always works......for a little while and then I have to repeat the steps.
The repair says check my wireless card ....and I swear thats not the issue.
Any ideas on how to fix. By the way I use have AMD Turion X2 64.
thanks
With all due respect you are thinking/limiting it to a wireless issue. I'm saying it's NOT just wireless connections. At home (all wireless) I have never had the issue.On my test Windows 7 RC1 desktop at work I often get the "Limited Connectivity" warning, but as far as I can tell everything is working fine (I can browse the net fine using Firefox and I get no drops from applications that access systems over the local network). This is a hardwired connection and we don't do wireless. We use Cisco switches/routers. I assumed it has something to do with the way it "discovers" if you have internet access. I'm on a corporate network with over 5000 users that spans the entire state with multiple "main" offices around the state.
with all due respect...since you're using a "wired" connection, and this is a thread about "wireless internet problems", your comment does nothing to help anyone.- Hi, I have much problem whit Conceptronic 54 Wireless (c54ri). I cann't connect to internet. If I connect whit ethernet of mother board, I can connect to internet.
- Hello all. I am also in the same boat. HP dv6000 with a broadcom wireless adaptor. I have tried turning off the homegroup and have installed the windows update for the broadcom card and have done all the same troubleshooting listed in this post. I still show limited connectivity (no internet) but I do have internet and it seems to stay connected now after the update. I can not connect to my work VPN because I need to be connected to the internet (even tho I am). Frustrating. My hardwire LAN is fine. I will post when I find the solution.
- Just an update on the hibernation problem. It seems on my Thinkpad T60, W7RC 64bit doesn't like to hibernate when I uncheck the option to allow windows to power off the device to save power. Once I checked that option, bam! I can hibernate again. What a wonderful thing...On another note, I'm not sure what this is all about, but I still have the issues everyone else is having with the wifi connection, like I have the yellow exclamation point and limited connectivity, but if I open up outlook 2007 before I use a web browser, the connectivity problem disappears and I can download my mail, then I can also use the internet. Maybe if I scratch my back with my left pinky while I hop around counterclockwise...all of my problems will go away?
- I solved my problem (Acer Laptop with broadcom wireless adapter) by installing the latest broadcom driver, version 5.10.79.7.
No more disconnects or limited connectivity after resuming from sleep or hibernation. Hope it helps some of you. Hi,
Is anyone still having issues after installing latest updates from Windows Update? If so, can you provide the following
--- make/model of the Wi-Fi card. You can get this by typing "netsh wlan sho dr" on the command prompt
----make/model of your Wi-Fi router
--- problem symptoms
--- reproduction steps for problem to happen
Thanks very much,
Taroon Mandhana[MSFT]I solved my problem (Acer Laptop with broadcom wireless adapter) by installing the latest broadcom driver, version 5.10.79.7.
No more disconnects or limited connectivity after resuming from sleep or hibernation. Hope it helps some of you.
I installed the last driver as you told, but after i did it the conection not response, get a red X on the signal icon, i restart the laptop, but the same, the poperties told me that the device is working fine, but i did not get any signal, i had to unistall the driver and install the original driver for HP.
Now is working fine, but for how long I do not know
I got a HP Pavilion DV6225US
Regards- Finally, after much gooogling and a sh*t load of headache, I've managed to solve my problems with Wi-Fi.Here are the steps i took:
1.Uninstall my network driver(Computer Management Console-Device Drivers-NetworkAdapters-Broadcom 802.11b/g-uninstall).
2.Uninstall the Broadcom Install utility(Control Panel-Uninstall a program-Broadcom Install Utility-Uninstall). In fact remove ANYTHING that has Broadcom on it!
3.Restart System.
4.Install Broadcom Driver version 4.102.15.61. This one is an OLD driver. But it works flawlessly(So far!).Here's where i got it from: http://drivers.softpedia.com/get/NETWORK-CARD/Broadcom/Broadcom-BCM943XX-Driver-4-102-15-61.shtml
5.Thats it! No more wi-fi headaches in windows 7 RC!
Really, I must say: BEST OF LUCK! - In fact, you could even use the default windows driver after uninstalling the broadcom utilities.
Finally, after much gooogling and a sh*t load of headache, I've managed to solve my problems with Wi-Fi.Here are the steps i took:
1.Uninstall my network driver(Computer Management Console-Device Drivers-NetworkAdapters-Broadcom 802.11b/g-uninstall).
2.Uninstall the Broadcom Install utility(Control Panel-Uninstall a program-Broadcom Install Utility-Uninstall). In fact remove ANYTHING that has Broadcom on it!
3.Restart System.
4.Install Broadcom Driver version 4.102.15.61. This one is an OLD driver. But it works flawlessly(So far!).Here's where i got it from: http://drivers.softpedia.com/get/NETWORK-CARD/Broadcom/Broadcom-BCM943XX-Driver-4-102-15-61.shtml
5.Thats it! No more wi-fi headaches in windows 7 RC!
Really, I must say: BEST OF LUCK!
Thanks buddy it worked for me as well, though I have Dell wireless adapter. I have just uninstall the original one and reinstall it thats it. I have no idea whats the logic behind this but its working. Now my pc is connected back to internet after the sleep mode.
:)- Geely/Ajay,
For the current state, can you try to update to the latest broadcom driver on Windows update and see if it works for correctly for you?
How did you get this broadcom install utility? Was it present before upgrade?
Thanks.
Taroon [MSFT] - Danverc,
Do you also have the broadcom utility installed on your machine?
Thanks.
Taroon Ajay.ramesh/Jleecong/Badomens,
You all reported that you got "limited connectivity" while you were able to browse the Internet. Do you need to manually configure proxies to reach the Internet? Does it still repro for you? If so could you help us gather the logs so that we can invesitgate the issue further? Here is the tracing instruction (from an elevated command prompt):
- netsh trace start nid_wpp capture=yes
- repro
- netsh trace stop
The last command will print out the location of the cab file and you can send it to tinqian@microsoft.com.
Thank you very much for selfhosting windows 7!
Tin Qian [Microsoft]- catalinux,
We are interested in finding out why home group was the cause of the router issues that you were experiencing. Can you re-enable home group to see the problem still reproes? If so, could you help us collect the logs (from elevated command prompt):
- netsh trace start internetclient capture=yes persist=yes
- repro (ok to reboot if necessary for the repro)
- netsh trace stop
The last command will print out the location of the cab file and you can send it to tinqian@microsoft.com. We will investigate and post back to the forum the findings and recommendations.
Thank you for self-hosting windows 7,
Tin Qian [Microsoft] Geely/Ajay,
There is one thing i want to highlight:
For the current state, can you try to update to the latest broadcom driver on Windows update and see if it works for correctly for you?
How did you get this broadcom install utility? Was it present before upgrade?
Thanks.
Taroon [MSFT]
When I have vista installed it detects my WiFi adaptor as a Broadcom. And in W7 it detects as a Dell Wireless 1390 WLAN Mini-card. STRANGE!
I got this Broadcom Install utility from this post of [ajay.ramesh Saturday, May 23, 2009 4:51 AM ]
I have tried to install the broadcom drivers but W7 detects as the Dell wifi and installs the driver automatically overriding my broadcom installation.
As far as upgrade is concerned i am afraid to take the risk of upgrading it form windows update, what if i get the previous bug back to my PC, since my bug is vanished currently.
- If your problems are detected in the troubleshooter as driver issues (both for cabled and wireless network), you have to restore your windows at the date of for example 15 of may. i've troubleshooted my problem like that, then i could connect and update my system.
Danverc,
Do you also have the broadcom utility installed on your machine?
Thanks.
Taroon
Taroon,
After a short time I got the same trouble, I tried to uninstall again the driver from HP, but I could not do it, so I did a clean instalation again, this time I did not install any broadcom driver, just driver from W7, actually I am not installing the driver from windows update, I had a lost signal for a few moment, and the system conect it again but itself.
RegardsDan, do you have the W7 system losing the connection on its own periodically after the clean install?
Thanks.Same problem. regular internet browsing.. suddenly wireless stop. I am glad I had time to write this post. I never know how long time I am given on the net... Rebooting is the only remedy.. My machine is useless now.
Ok, so right after i posted this, I noticed that an update for my Broadcom 802.11g Network Adapter was ready for download and install at Windows Update. ofcourse my networked hanged, but i restarted, and did the update. And now everything seems to work just fine!!! great! 30min online, downloaded big files, no problem so far!Acer TravelMate 5510
The latest driver update fixed the problem for me as well. I have a Linksys Wireless-N network adapater. However, Win7 applies Broadcom driver to it and it worked. It's been 2 days since I last lost network connection.Dan, do you have the W7 system losing the connection on its own periodically after the clean install?
Thanks.
Taroon, Actually I do not lose the connection, I downloaded big files, and it is working fine now
Regards
I have a Linksys WUSB54GS v2.1 here, and had this exact issue, along with some others. I did a clean reinstall, installed the Windows XP 64bit drivers that I was using in rel7000, which got me onto the web, then I ran an update and installed the drivers recommended byt MS update. That seems to have been the end of my woes!Same problem. regular internet browsing.. suddenly wireless stop. I am glad I had time to write this post. I never know how long time I am given on the net... Rebooting is the only remedy.. My machine is useless now.
Ok, so right after i posted this, I noticed that an update for my Broadcom 802.11g Network Adapter was ready for download and install at Windows Update. ofcourse my networked hanged, but i restarted, and did the update. And now everything seems to work just fine!!! great! 30min online, downloaded big files, no problem so far!Acer TravelMate 5510
The latest driver update fixed the problem for me as well. I have a Linksys Wireless-N network adapater. However, Win7 applies Broadcom driver to it and it worked. It's been 2 days since I last lost network connection.- It's NOT about the Broadcom Install Ultility. It's about DRIVERS. Windows 7 is incompatible with MOST other drives. Typical scenarios are given in detail in my first post( the topic starter post, in fact). Just go to the Computer management console and uninstall whatever Wi-fi driver you have and then in the same console hit Action---Scan Hardware changes. A new DEFAULT driver should be automatically installed and your Wi-fi problems will go away!
Hope this helps! - The Broadcom driver are suiatable for several cards including my Linksys WMP300.
The drivers have a profound impact on latency. Allowing Win7 to obtain the latest drivers will result in high latency, and for many users this translates into audio problems.
The driver with the lowest latency is the one supplied by MS for Vista - 4.102.15.61.
However, this release also stops at irregular intervals leaving the adaptor unresponsive, so sorry to say it is not a cure.
So, the bottom line: Allow Windows to install and upgrade the driver and have buggy sound and intermittent network failures, or install the 4.102.15.61 driver and enjoy good sound whilst the connection lasts.
I agree with other posters that the disconnect issue is driver related. But I would love to hear from MS their take on the problem and a description of what's changed in this area compared to Vista.
Manybe we should also be pestering Linksys and Broadcom to investigate too.
Duckysan - I'm also having this problem. I'm running the x64 bit version of build 7100 on my HP tx1220ca (part of the tx1000 touch family). It has a Broadcom wi-fi with wireless N and I'm connecting to a wireless N network build on a D-Link router. Interestingly when I set the router to broadcast in wireless N mode only, the laptop refuses to connect at all although it can usually detect the router (often it doesn't) while other wireless computers running Vista on the network do not seem to have any issues. This may or may not be related but I thought it strange.
While my fiancé can connect with her HP laptop running Vista to the wi-fi network without difficulties, my laptop behaves exactly as is described above. It will connect to the network and usually the internet upon a fresh boot if the router is set to broadcast in all modes (802.11 b/g/n). It will stay connected for a seemingly random amount of time ranging from around 1 minute to about 30 minutes. It will then disconnect or show connectivity problems by way of the yellow triangle and exclamation mark and will refuse to connect properly until the system has been rebooted. Occaisionally it does re-connect and the triangle goes away but nothing on the network is accessible or even visible despite there being no message indicating limited connectivity and having full bars. The internet is also inaccessible despite an apparently solid connection.
Interestingly I do not appear have connectivity problems when the laptop is in tablet mode which lead me to briefly contemplate that maybe the wi-fi antenna had something to do with it until I found this post where it is obvious that others are having identical issues on different hardware. Also, the wi-fi worked flawlessly under Vista on the same hardware only two weeks ago. On a side note, it appears that the connection can be maintained when the laptop is located right next to the wireless router (as in literally on the same desk) so perhaps the issue has something to do with signal fault tolerance/interference? I haven't tested that theory out yet so I'm just floating the idea.
Troubleshooting
To troubleshoot the problem (sadly without success) I've installed the latest Microsoft-provided driver for my Broadcom device. The latest driver seemed to actually make the problem worse by increasing the connectivity problems. I've since reverted to an older, HP supplied driver which has allowed me to at least have some connectivity after reboots. I have tried turning the wi-fi device off and then back on with no effect. I have also tried the diagnostic tool several times which tells that my router needs to be rebooted. I did reboot my router and actually reset it to factory defaults based on diagnostic advice (and rebuilt the network from scratch as I had to reset and configure a wireless bridge as well) but the issue persists. Seeing as both Vista and the Windows 7 Beta did not have this problem I feel that it must be something in the RC build that is causing the problems. - I am,
-- Wi-Fi card: Broadcom 4322AG 802.11a/b/g/draft-n Wi-Fi Adapter
-- Router: D-Link DIR-625
-- Laptop: HP TX1220ca running x64 Win7 build 7100
-- Laptop connects to LAN and internet upon bootup but loses internet connectivity after a varying and seemingly random amount of time. It continues to indicate a strong LAN connection but no LAN resources are visible or accessible. Eventually it indicates a LAN connection loss and will fail to reconnect properly until the laptop is reboot. I had the latest drivers which seemed to make the problem worse and have since gone back to latest HP supplied Vista x64 drivers which allow for consistent connections upon reboots.
-- No specific action seems to cause the problem. It simply happens while using the internet after a certain amount of time but will happen for sure if the computer is allowed to sleep. It's NOT about the Broadcom Install Ultility. It's about DRIVERS. Windows 7 is incompatible with MOST other drives. Typical scenarios are given in detail in my first post( the topic starter post, in fact). Just go to the Computer management console and uninstall whatever Wi-fi driver you have and then in the same console hit Action---Scan Hardware changes. A new DEFAULT driver should be automatically installed and your Wi-fi problems will go away!
Hope this helps!
^seconded
Tried and tested its working for me.- I have same problem both wireless and wired.. keeps losing connection, I have tried every browser still same thing.. My other 2 laptops side by side does not lose connection, I have updated all drivers etc.. I am using RC ulimate and after 5 mins. I lose connection! I guess the drivers just are not supporting this OSbeta yet? That is only explanation as only have problem with beta version!Christopher
- I just tried that a minute ago and it didn't work for me. Any other ideas?
Still having similar issues with the Windows 7 RC.
I have a HP6730b notebook with an Intel 5100 AGN WIFI network adapter.
After boot it takes about 2 minutes before a wireless connections is established.
Until the connection is made the GUI shows a limited connection.
Odd thing is that with an limited connection I expect to receive an APIPA address. This is not the case.
I have tried older intel drivers and newer drivers. This does not seem to make a difference.
Currently using the drivers from Microsoft. ( 12.4.1.4)
There are a couple of programs that interfere with the network card.
Kaspersky AntiVirus 8.0 (beta)
Cisco VPN client 5.0.01.0600
Trying to uninstall these applications did not resolve the issues.
To make things even more puzzling. This issue started a few weeks ago. Before this I have never had this problem. Connection was always established within a few seconds. Unfortunatly I cannot go back in time (system restore) to the period before the problems appeared.
I am not sure what more options I have left.
I doubt updating router firmware will solve this problem. Other Windows 7 RC clients can connect just fine.
Any ideas are most welcome.
Remko- for some reason my broadcom driver keeps updating by itself...idk why whenever...oh btw I'm doing your procedure by uninstalling it and installing a previous version of it
It's NOT about the Broadcom Install Ultility. It's about DRIVERS. Windows 7 is incompatible with MOST other drives. Typical scenarios are given in detail in my first post( the topic starter post, in fact). Just go to the Computer management console and uninstall whatever Wi-fi driver you have and then in the same console hit Action---Scan Hardware changes. A new DEFAULT driver should be automatically installed and your Wi-fi problems will go away!
OK i uninstalled the broadcom driver and did the scan hardware changes and it works...but i think it goes back to the same driver version i had that keeps disconnecting after the first couple minutes...i'm not sure
Hope this helps!- This is a real deal-breaker for me, it is not an issue with XP - it shouldn't be with a NEW operating system at the RC level.. The sad thing is Microsoft does not address nor give guidance for a resolution to the problem. Pathetic.
- I'm having various networking problems across several laptops and a desktop both wired and wireless. The main issue is that I can access certain servers without any problems whatsoever and others are either very slow or just don't connect at all. Sometimes downloading an .exe will finish and will be corrupted as well. Hulu and Nvidia give me problems, for instance, but google and other websites seem to be fine. For instance if I go to www.speakeasy.net/speedtest I can connect and get regular bandwidth speeds with the Washington, D.C. server for instance, but with the New York server my bandwidth trickles down or can't connect at all.
- I had the same connectivity issue with my Linksys WUSB300N wireless card. It would connect sporadically and then disconnect after a few minutes. I scoured all the boards, and tried all the fixes to no avail. In a desperate fit of frustration I decided to try something different. I enabled IPV6 and I set up a Homegroup. Voila... flawless ever since. The only reason I suspect this worked was that maybe Windows somehow reset how it saw my wireless card. If you already have a Homegroup set up, try leaving it and setting it up again. Can't hurt, right?
Luck to All. - Have the exactly same problem with my Dell inspiron 1520. After a few minutes or so, i lost connection and can't reconnect again. I have to reboot to connect again, but the problem happens again(using 7100). But when i first installed win 7, i did not have any problems and surfed like 7-8 hours without any problem. After, i updated my drivers and the connectivity problem showed up.
I will try to uninstall drivers.Hope it works, cuz it really pisses me off, and i am starting to think to use vista again. - We are having the same Problems "Very slow WiFi speeds) with lots of different hardware tested!!! We are using the RTM 76000 16385 build. none of the above solutions worked. we had to use LAN 10/100/1000 Cables to "solve" the problem. with LAN cable connected you dont have to do anything from the above (maybe disable QOS in router and Card protocols) But everything works fine, maximum speeds all the time. Wifi after disable-enable works for a while and then just slows down terrible! with the same Hardware we had NO ISSUES in Vista x64 or XP x64. i cant believe Microsoft cant find right away a solution to this serious problem, so far we have found no other issues using the OS.
- I FIND the solution for me.
its all about the damn Drivers After all!
ok i managed to make to combine the Windows xp x64 driver and the Vista x64 driver of my TL-WN322G and i made a new 100% workable driver for Windows 7 x64!
i have the link here, it will work for some other TP-Link usb wifi too. install it even it says its not signed. The driver works perfectly so far. Also in the ZIP file you will find the TCP-IP optimizer for windows 7/vista, use it and you will gain much more speed and acceleration!
TL-WN322G Windows 7 x64 Driver Here: http://synapse.gr/downloads/TL-WN322G Windows 7x64.zip- Edited byJohnnyXP64 Thursday, July 23, 2009 9:06 PM
- I was having the same problems with build 7100. I tried everything I knew to get this fixed. I spent hours searching the internet trying to find a solution. In the end all I had to do to fix my problem was to change from WPA2 to WEP security on my router and everything has been working perfectly for over a week now. I don't know if this will solve everyone's problem but it certainly solved mine. Hope this helps...
- In fact, you could even use the default windows driver after uninstalling the broadcom utilities.How do I do this?
- I built a new system (Intel Core 2 Quad Q6700 Processor 2.66GHz, 8MB Cache, 1066MHz FSB, 4GB RAM, Kentsfield, Quad-Core, OEM, Socket 775, Processor with Intel DG35EC Motherboard - Intel G35 Express, Socket 775, MicroATX, Audio, Video, DVI, PCI Express, Gigabit LAN, USB 2.0, FireWire, Serial ATA), and installed, clean, 64 bit version Windows 7 RC 7100. Using USB wireless Linksys adapter, was getting great speeds to the internet and no problems with just IE8 running. Then I up'd the ante with Windows Live Messenger and Secondlife and evony running. Lag increased and performance decreased and then the internet connection started dropping every 10 minutes, would auto reconnect within a minute and go for 10 more and drop again. Over and over. Very annoying. I noticed the issue started after 7 windows updates were applied from the build 7100 I was at (base 7100?). My Linksys router was already using WEP security. I plan to try some of the ideas I am reading here, but would love to see a windows update come down to fix this issue for all of us once and for all. My other 4 PC's on the home LAN, all wireless, are running Vista and XP home and have no issues.
Taroon Manhana,
Latest driver causes this problem.
The driver netsh below FIXES this problem (for me at least)
Microsoft Windows [Version 6.1.7100]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.C:\Users\William>netsh wlan show driver
Interface name: Wireless Network Connection
Driver : Broadcom 802.11b/g WLAN
Vendor : Broadcom
Provider : Broadcom
Date : 12/19/2006
Version : 4.102.15.61
INF file : C:\Windows\INF\oem18.inf
Files : 1 total
C:\Windows\system32\DRIVERS\BCMWL664.SYS
Type : Native Wi-Fi Driver
Radio types supported : 802.11g 802.11b
FIPS 140-2 mode supported : No
Hosted network supported : No
Authentication and cipher supported in infrastructure mode:
Open None
Open WEP
Shared None
Shared WEP
WPA2-Enterprise TKIP
WPA2-Personal TKIP
WPA2-Enterprise CCMP
WPA2-Personal CCMP
WPA-Enterprise TKIP
WPA-Personal TKIP
WPA-Enterprise CCMP
WPA-Personal CCMP
Authentication and cipher supported in ad-hoc mode:
WPA2-Personal CCMP
Open None
Open WEP
C:\Users\William>- I just installed Win 7 RC on my fiancee's HP DV6600 series laptop and it's having a similar issue to my Tx1000 series. Interestingly though, I brought a Wireless B/G-only router online and her laptop has no trouble connecting to that but it has some issues connecting to our normal D-Link wireless N router. I'm thinking maybe it's a problem related to Win 7 and the wireless N (draft) standard? I haven't yet tried disabling N on the D-Link router because my tx1000 still uses N but perhaps it's simply a problem with "N" and not the router or wi-fi card??
- Well, it kinda fixed it for me to use that old driver... It connected coming out of sleep mode, but it started just randomly dropping connection at various other times... i'm back on latest driver and rebooting to be able to connect to internet
- Same issue here it would seem - mine's Linksys WUSB54GSC / tried multiple drivers and can't seem to get one that makes a difference / the broadcom driver listed won't enable the device to 'start' so no big thing there.Have attempted making the router specific to B only - no difference. Considering looking at a log of FileMon / RegMon to watch when I lose my conectivity but that's a lot to read through./waits for the update
- One other thing I would suggest to check is the power saving setting on your monitor. Usually there is a button or button combination on the monitor you can press which allows you to access its settings. I noticed that whenever my monitor went to sleep, the wireless network would disconnect (even though all the windows power savings settings were disabled). When I turned off power saving on the monitor, the problem disappeared.
Hope this helps.
Mark - same exact problem with me