scaned by workgrp is work but by ip is failed

Tutte le risposte

• sabato 11 febbraio 2012 01:21

  Moderatore

   

   
  

  0
  What are the failure types? i.e. Failed – Machine not found, Failed – Connection Timeout, etc.

  ---

  Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

  • Risposta
  • Citazione

   
• lunedì 13 febbraio 2012 13:53

   

   
  

  0

  hello Michael,

  scan by workgrp. all work fine
  scan by IP range first time, almost no PC found, and no errors displayed. WMI and Registry all failed.
  scan by ip range sec time, selet ip range 192.168.1.2 - 192.168.1.253 while scanning i saw
               success failure object count
  WMI           9       243        0
  Registry      0       252        0
  one 1 PC is connection refused.
  and 1 is success which is show o/s = insufficient data and service pack= insufficient data.
  but they are actually not yet pre-config for inv scanning. not ready
  Machine Summary and Application summary is empty, i guess because object count is = 0;

  BUT EVEN MY OWN PC is missing, dose it because the tools will not scan own IP address ?
  but scan by workgrp i can see my own PC inv.

  scan by IP range thrid time, i enter my PC ONLY and scan again, now INCLUDED some PC which
  was not able to scan. now is success and see the inv, total 6 PC can see inv, but we got abt
  80 PC, again, by workgrp is 95% work fine, except few PC i not have time to prepare.

  so should i try again
  more info For your ref.
  Ping computer name got echo reply
  ping -a 192.168.1.101 got echo reply but no named resolved. do i really need the
  resolve host name if i used ip methods ?

  my inv.bat file for winXP, let me know if anything missing or wrong.
  -------------------------------------------------------------------------------------------------------

  @echo off
  reg add HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa /v forceguest /t REG_DWORD /d 0000 /f
  gpupdate

  sc stop RemoteRegistry
  sc config RemoteRegistry start= "auto"
  sc start RemoteRegistry

  netsh firewall set service RemoteAdmin enable
  netsh firewall add portopening protocol=tcp port=135 name=DCOM_TCP135
  netsh firewall set service type=fileandprint mode=enable profile=all
  echo done !!
  exit
  ----------------------------------------------------------------------------------------------------------------
  pls comments, keep trying but no luck

  thanks & appricated for your help
  regards
  Billy

  
  

  • Modificato billma9999 lunedì 13 febbraio 2012 13:57
  •  
  • Risposta
  • Citazione

   
• lunedì 20 febbraio 2012 18:39

  Moderatore

   

   
  

  0

  Yes, MAP needs to be able to resolve an IP to a host name or FQDN. Have you checked for any master browser or NETBIOS problems on your network?

  ---

  Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

  • Risposta
  • Citazione

   
• giovedì 23 febbraio 2012 06:59

   

   
  

  0

  yes Mic.

  netbios name is sure work, otherwise why workgrp is work perfect ?

  i finally found out the problem, i use 6.5 on winXP sp3.

  when i switch to win7. all work fine. i can scan subnet too.

  it drive me crazy and spent lot of time to trace all details include wmi..

  anyway. support job like this. just do it or leave support field.

  thanks

  regards

  Billy

  • Contrassegnato come risposta billma9999 sabato 25 febbraio 2012 04:49
  •  
  • Risposta
  • Citazione