locked
Lync Phone edition firmware update for different site RRS feed

  • Question

  • Hi, 

    We have 1 main site and 5 different SBA sites.

    Can we separate different site update Lync Phone edition firmware schedule?

    Or If I tested deploy firmware successfully upgrade on few phones and then deploy all sites at one times?

    It difficult to support , if 6 sites Lync Phone edition have problem together.

    Thanks.

    Saturday, October 1, 2016 3:00 PM

Answers

  • Hi Mick.

    You can run different LPE editions on different frontend pools, but not on an SBA, as this appliance does not host a webservice for UCUpdates.

    When you install a new version, you should test it on a few test device before approving the update to the rest of the devices.The schedulee for update is controlled by the device and is executed every 24 hours, when the device has been idle for 5 minutes, touch the device and the counter resets, so patience is a virtue.


    Kenneth ML || Please remember, if you see a post that helped you please click Vote on the left side of the response, and if it answered your question please click Mark As Answer.

    • Proposed as answer by jim-xu Monday, October 3, 2016 6:17 AM
    • Marked as answer by JohnHK215 Tuesday, October 4, 2016 2:34 PM
    Sunday, October 2, 2016 8:58 AM
  • Hi Mick,                                                                                                          

    Welcome to our forum.

    In addition to above suggestions, please refer to the following link to check how to “Configure Test Device”:

    http://blog.schertz.name/2011/01/updating-lync-phone-edition-devices/

    Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.


    Best Regard,
    Jim Xu
    TechNet Community Support


    Please remember to mark the replies as an answers if they help and unmark them if they provide no help.
    If you have feedback for TechNet Subscriber Support, contact tnmff@microsoft.com.

    • Marked as answer by JohnHK215 Tuesday, October 4, 2016 2:34 PM
    • Unmarked as answer by JohnHK215 Tuesday, October 4, 2016 2:34 PM
    • Marked as answer by JohnHK215 Tuesday, October 4, 2016 2:34 PM
    Monday, October 3, 2016 6:28 AM

All replies

  • Hi Mick.

    You can run different LPE editions on different frontend pools, but not on an SBA, as this appliance does not host a webservice for UCUpdates.

    When you install a new version, you should test it on a few test device before approving the update to the rest of the devices.The schedulee for update is controlled by the device and is executed every 24 hours, when the device has been idle for 5 minutes, touch the device and the counter resets, so patience is a virtue.


    Kenneth ML || Please remember, if you see a post that helped you please click Vote on the left side of the response, and if it answered your question please click Mark As Answer.

    • Proposed as answer by jim-xu Monday, October 3, 2016 6:17 AM
    • Marked as answer by JohnHK215 Tuesday, October 4, 2016 2:34 PM
    Sunday, October 2, 2016 8:58 AM
  • Hi Mick,                                                                                                          

    Welcome to our forum.

    In addition to above suggestions, please refer to the following link to check how to “Configure Test Device”:

    http://blog.schertz.name/2011/01/updating-lync-phone-edition-devices/

    Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.


    Best Regard,
    Jim Xu
    TechNet Community Support


    Please remember to mark the replies as an answers if they help and unmark them if they provide no help.
    If you have feedback for TechNet Subscriber Support, contact tnmff@microsoft.com.

    • Marked as answer by JohnHK215 Tuesday, October 4, 2016 2:34 PM
    • Unmarked as answer by JohnHK215 Tuesday, October 4, 2016 2:34 PM
    • Marked as answer by JohnHK215 Tuesday, October 4, 2016 2:34 PM
    Monday, October 3, 2016 6:28 AM
  • Thanks for the reply.

    If we have two front end pools , the LPE is registered on A pool, LPE will update A pool firmware version only?

    B Pool have new firmware , if no LPE registered on B pool, it will not update right? 

    But SBAs is follow backup pool A pool web services LPE firmware right?

    Monday, October 3, 2016 1:10 PM
  • Hi Mick.

    Correct.

    Correct.

    Correct.


    Kenneth ML || Please remember, if you see a post that helped you please click Vote on the left side of the response, and if it answered your question please click Mark As Answer.

    Tuesday, October 4, 2016 6:03 AM