locked
Error 11 atapi RRS feed

  • Question

  • System
    - Provider
    [ Name] atapi
    - EventID 11
    [ Qualifiers] 49156
    Level 2
    Task 0
    Keywords 0x80000000000000
    - TimeCreated
    [ SystemTime] 2013-03-10T18:57:38.248619100Z
    EventRecordID 125751
    Channel System
    Computer Melody-HP
    Security
    - EventData
    \Device\Ide\IdePort2
    0000100001000000000000000B0004C004000000850100C00000000000000000000000000000000000000000000000000000000005100000

    Binary data:

    In Words

    0000: 00100000 00000001 00000000 C004000B
    0008: 00000004 C0000185 00000000 00000000
    0010: 00000000 00000000 00000000 00000000
    0018: 00000000 00001005

    In Bytes

    0000: 00 00 10 00 01 00 00 00 ........
    0008: 00 00 00 00 0B 00 04 C0 .......À
    0010: 04 00 00 00 85 01 00 C0 ....…..À
    0018: 00 00 00 00 00 00 00 00 ........
    0020: 00 00 00 00 00 00 00 00 ........
    0028: 00 00 00 00 00 00 00 00 ........
    0030: 00 00 00 00 05 10 00 00 ........

    Sunday, March 10, 2013 7:05 PM

Answers

  • Hi,

     

    Based on my research, these messages are posted because of hardware problems. The source may be the controller or (more probably) a device that is attached to the controller. The hardware problem can be poor cabling, incorrect termination or transfer rate settings, slow device relinquishment of the SCSI bus, a faulty device, or in rare cases, a poorly written device driver.

     

    Please go to Device Manger to update the IDE controller driver to check the result.

     

    Also check the following Microsoft KB to see whether it could help:
    How to troubleshoot event ID 9, event ID 11, and event ID 15 error messages

    Thanks.


    Vincent Wang
    TechNet Community Support

    Tuesday, March 12, 2013 6:53 AM

All replies

  • Hi,

     

    Based on my research, these messages are posted because of hardware problems. The source may be the controller or (more probably) a device that is attached to the controller. The hardware problem can be poor cabling, incorrect termination or transfer rate settings, slow device relinquishment of the SCSI bus, a faulty device, or in rare cases, a poorly written device driver.

     

    Please go to Device Manger to update the IDE controller driver to check the result.

     

    Also check the following Microsoft KB to see whether it could help:
    How to troubleshoot event ID 9, event ID 11, and event ID 15 error messages

    Thanks.


    Vincent Wang
    TechNet Community Support

    Tuesday, March 12, 2013 6:53 AM
  • Hi,

    Am having frequent boot up failures - BIOS is loaded, but PC stalls at "Starting Windows" splash screen (4 coalescing balls of colour don't appear), PC hangs, and has to be powered off/on to proceed. Restart in Windows fails completely every time, PC shuts down but doesn't restart - goes to black screen, but no startup.  Event viewer displays error type 11, with following message:

    "The driver detected a controller error on \Device\Ide\IdePort0."

    Have gone into Device Manager, and Windows confirms most up-to-date drivers are installed already for all IDE channel 0, 1, 4 and 5, also AHCI controller and IDE controller entries.

    I've had problem with 2 different 1TB SATA HDDs, and with different DVD/Bluray drives, so doesn't seem related to a specific faulty SATA device.  Have also tried swapping SATA ports on the motherboard, and using different SATA cables - no effect.

    Please advise what else I can try.  OS is Windows 7 64-bit, MB is an Asus P5KC with latest rev 12.03 BIOS.

    Thanks.


    • Edited by gwwishart Sunday, March 23, 2014 11:11 PM
    Sunday, March 23, 2014 11:06 PM
  • In my case a bad sector caused this error message in the Windws System Log.

    At first I cleaned all cables and changed the order of the cables and the referred port is also changed. I disabled the CD-ROM, but there was no result.

    It was very strange, becae the message was every day in the same time... later I realised that the the message appear when the Kaspersky scan is running!!!!

    I suspected it that there is a problem with the HDD. So I run the "HDD Seintel" in order to find the problem. The result of the SMART tests was excellent, but there was a warning message about BAD SECTOR in the HDD Seintel diary. So I run the built-in chkdisk at the next Windows restart and the "atapi error 11" message has disappeared.
    Monday, April 1, 2019 6:57 AM