locked
Intel(R) ICH9 Family SMBus Controller - 2930/HL-DT-ST DVD+-RW GT10N ATA Device conficking RRS feed

  • Question

  • HL-DT-ST DVD+-RW GT10N ATA Device, Location 0 (Channel 1, Target 0, Lun -A driver (service) for this device has been disabled.  An alternate driver may be providing this functionality. (Code 32)

    Intel(R) ICH9 Family SMBus Controller - 2930, Location  PCI bus 0, device 31, function 3--This device cannot find enough free resources that it can use. (Code 12)

    If you want to use this device, you will need to disable one of the other devices on this system. The sata HDD on channel 0

    Is sharing the same smbus 2930 as the dvd on channel 1 and there's 4 channels so out of resources. Any ideas?

    Tuesday, June 30, 2015 10:33 AM

Answers

  • Hi,

    The error Code might be caused by a temporary problem with the hardware. If so, a restart of your computer might be all you need to fix the Code 32 error. If you install a device or make a change in Device Manager just before the Code 32 error appeared, depending on the changes you made, some solutions might include:

    Remove or reconfigure the newly installed device.

    Roll back the driver to a version prior to your update.

    Using System Restore.

    Since it looks like a DVD device, one common cause of Code 32 errors is the corruption of two registry values in the DVD/CD-ROM Drive Class registry key. If that is the case, try follow the instructions as mentioned below to remove the UpperFilters and LowerFilters

    http://pcsupport.about.com/od/driverssupport/ht/upperfilters-lowerfilters.htm

    IMPORTANT: This article contains information about editing the registry. Before you edit the registry, make sure you understand how to restore it if a problem occurs. Since the website is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.

    If it is an USB device is generating the Code 32 error, uninstall every device under the Universal Serial Bus controllers hardware category in Device Manager as part of the driver reinstall. This includes any USB Mass Storage Device, USB Host Controller, and USB Root Hub.

    For code 12, two devices have been assigned the same input/output (I/O) ports, the same interrupt, or the same Access channel. The assignment was made by either the basic input/output system (BIOS), the operating system, or a combination of the two. So your suspicion makes sense.

    Since the resolution for this issue can be very hardware specific. So make sure you updated chip set driver/BIOS form Inter for good measure, and try referring to Inter community for “code 12” and detailed information about your hardware type, name, or model number.

    If the issue still persists, as mentioned by Rick, I'd suggest address this to Inter support, There
    you might get more effective suggestion by other experts who familiar with design
    of Inter products. Your understanding is highly appreciated.

    Regards,

    D. Wu


    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact tnmff@microsoft.com.


    Wednesday, July 8, 2015 1:38 AM
  • Technet is a bit short on this topis, however points to cause correctly

    https://technet.microsoft.com/cs-cz/library/cc771230(v=ws.10).aspx

    Consider troubleshooting according to this article

    http://pcsupport.about.com/od/errorc/a/code-32-error.htm

    HTH

    Milos

    Wednesday, July 8, 2015 1:58 AM

All replies

  • You should address this to Intel Technical Support as they are much better qualified to discuss this and may well have a solution for you!


    Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ”

    Saturday, July 4, 2015 11:41 AM
  • Hi,

    The error Code might be caused by a temporary problem with the hardware. If so, a restart of your computer might be all you need to fix the Code 32 error. If you install a device or make a change in Device Manager just before the Code 32 error appeared, depending on the changes you made, some solutions might include:

    Remove or reconfigure the newly installed device.

    Roll back the driver to a version prior to your update.

    Using System Restore.

    Since it looks like a DVD device, one common cause of Code 32 errors is the corruption of two registry values in the DVD/CD-ROM Drive Class registry key. If that is the case, try follow the instructions as mentioned below to remove the UpperFilters and LowerFilters

    http://pcsupport.about.com/od/driverssupport/ht/upperfilters-lowerfilters.htm

    IMPORTANT: This article contains information about editing the registry. Before you edit the registry, make sure you understand how to restore it if a problem occurs. Since the website is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.

    If it is an USB device is generating the Code 32 error, uninstall every device under the Universal Serial Bus controllers hardware category in Device Manager as part of the driver reinstall. This includes any USB Mass Storage Device, USB Host Controller, and USB Root Hub.

    For code 12, two devices have been assigned the same input/output (I/O) ports, the same interrupt, or the same Access channel. The assignment was made by either the basic input/output system (BIOS), the operating system, or a combination of the two. So your suspicion makes sense.

    Since the resolution for this issue can be very hardware specific. So make sure you updated chip set driver/BIOS form Inter for good measure, and try referring to Inter community for “code 12” and detailed information about your hardware type, name, or model number.

    If the issue still persists, as mentioned by Rick, I'd suggest address this to Inter support, There
    you might get more effective suggestion by other experts who familiar with design
    of Inter products. Your understanding is highly appreciated.

    Regards,

    D. Wu


    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact tnmff@microsoft.com.


    Wednesday, July 8, 2015 1:38 AM
  • Technet is a bit short on this topis, however points to cause correctly

    https://technet.microsoft.com/cs-cz/library/cc771230(v=ws.10).aspx

    Consider troubleshooting according to this article

    http://pcsupport.about.com/od/errorc/a/code-32-error.htm

    HTH

    Milos

    Wednesday, July 8, 2015 1:58 AM