locked
system getting switch office RRS feed

  • Question

  • my office system getting switch off. when i check the logs i m getting below errors.

    1.when computer rebooted from bug check error 1001

    2.this errors the previous system shutdown was unexpected 6008

    3. the system has been rebooted without cleanly shutting down first id 41

    please help me out in this.................?

    Friday, July 11, 2014 10:39 AM

Answers

  • Refer this blog : http://arnavsharma.net/3/post/2014/06/track-windows-shutdown-using-event-logs.html






    Arnav Sharma | http://arnavsharma.net/ Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

    • Proposed as answer by arnavsharma Monday, July 21, 2014 4:25 AM
    • Marked as answer by Michael_LS Tuesday, July 22, 2014 11:32 AM
    Saturday, July 12, 2014 5:07 PM
  • The kernel power event ID 41 error occurs when the computer is shut down, or it restarts unexpectedly. When a computer that is running Windows starts, a check is performed to determine whether the computer was shut down cleanly. If the computer was not shut down cleanly, a Kernel Power Event 41 message is generated

    There are several reasons for this situation, in your situation, there may be a problem with the hardware. To help isolate the problem, check the following items:

    1.Overclocking: Disable overclocking to see whether the issue occurs when the system is run at the correct speed.

    2.Check the memory: Verify the memory by using a memory checker. Verify that each memory chip is the same speed and that it is configured correctly in the system.

    3.Power supply: Make sure that the power supply has enough wattage to appropriately handle the installed devices. If you added memory, installed a newer processor, installed additional drives, or added external devices, such devices can require more energy than the current power supply can provide consistently.

    4.Overheating: Check whether the system is overheating by examining the internal temperature of the hardware.

    5.Defaults: Reset the system back to the system defaults to see whether the issues occur when the system is running in its default configuration.

    If you see that the computer generates a Stop error that contains a BugcheckCode value that is not reported in an event ID 41, change the restart behavior for the computer. To do this, follow these steps:

    1.Right-click My Computer, and then click Properties.

    2.Click Advanced system settings.

    3.Click the Advanced tab.

    4.In the Startup and Recovery section, click Settings.

    5.Click to clear the Automatically restart check box.

    For more situations you can refer to this for detail:

    http://support.microsoft.com/kb/2028504#method3

    Regards


    Wade Liu
    TechNet Community Support

    • Proposed as answer by arnavsharma Monday, July 21, 2014 4:25 AM
    • Marked as answer by Michael_LS Tuesday, July 22, 2014 11:32 AM
    Tuesday, July 15, 2014 12:48 PM

All replies

  • Refer this blog : http://arnavsharma.net/3/post/2014/06/track-windows-shutdown-using-event-logs.html






    Arnav Sharma | http://arnavsharma.net/ Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

    • Proposed as answer by arnavsharma Monday, July 21, 2014 4:25 AM
    • Marked as answer by Michael_LS Tuesday, July 22, 2014 11:32 AM
    Saturday, July 12, 2014 5:07 PM
  • The kernel power event ID 41 error occurs when the computer is shut down, or it restarts unexpectedly. When a computer that is running Windows starts, a check is performed to determine whether the computer was shut down cleanly. If the computer was not shut down cleanly, a Kernel Power Event 41 message is generated

    There are several reasons for this situation, in your situation, there may be a problem with the hardware. To help isolate the problem, check the following items:

    1.Overclocking: Disable overclocking to see whether the issue occurs when the system is run at the correct speed.

    2.Check the memory: Verify the memory by using a memory checker. Verify that each memory chip is the same speed and that it is configured correctly in the system.

    3.Power supply: Make sure that the power supply has enough wattage to appropriately handle the installed devices. If you added memory, installed a newer processor, installed additional drives, or added external devices, such devices can require more energy than the current power supply can provide consistently.

    4.Overheating: Check whether the system is overheating by examining the internal temperature of the hardware.

    5.Defaults: Reset the system back to the system defaults to see whether the issues occur when the system is running in its default configuration.

    If you see that the computer generates a Stop error that contains a BugcheckCode value that is not reported in an event ID 41, change the restart behavior for the computer. To do this, follow these steps:

    1.Right-click My Computer, and then click Properties.

    2.Click Advanced system settings.

    3.Click the Advanced tab.

    4.In the Startup and Recovery section, click Settings.

    5.Click to clear the Automatically restart check box.

    For more situations you can refer to this for detail:

    http://support.microsoft.com/kb/2028504#method3

    Regards


    Wade Liu
    TechNet Community Support

    • Proposed as answer by arnavsharma Monday, July 21, 2014 4:25 AM
    • Marked as answer by Michael_LS Tuesday, July 22, 2014 11:32 AM
    Tuesday, July 15, 2014 12:48 PM