none
Winsock error code: 10060 RRS feed

  • Question

  • Hi everyone, 

    I am using Exchange Server 2013 CU7

    In the smtp send connector i can see these many logs, please guide me troublshoot

    Failed to connect. Winsock error code: 10060, Win32 error code: 10060, Error Message: 
    A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond X.X.X.X:25" X.X.X.X is public ip


    Thursday, June 18, 2015 8:16 AM

Answers

  • Hello

    tip: check firewall for 25 port


    sorry my english

    • Marked as answer by Risingflight Tuesday, June 23, 2015 12:41 PM
    Thursday, June 18, 2015 11:27 AM
  • Hi,

    Would you please post more details about your environment? For example, firewall, external mail flow and accept domain.
    How about internal or external mail flow?

    Please check the firewall port as Sneff mentioned. Then run below command to check the configuration for send connector, as well as accept domain:
    Get-SendConnector | FL
    Get-AcceptDomain | FL
    Note: pay attention to the IP range  and address space.

    Thanks


    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact tnmff@microsoft.com.

    Allen Wang
    TechNet Community Support

    • Marked as answer by Risingflight Tuesday, June 23, 2015 12:41 PM
    Friday, June 19, 2015 7:08 AM
    Moderator
  • Try to telnet to the IP over port 25.  If that fails, and it probably will based on the error message, I would first check your firewall and make sure you allow output SMTP traffic from your mail server, then I would check your ISP and make sure they don't blcok smtp traffic on port 25.

    Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread

    • Marked as answer by Risingflight Tuesday, June 23, 2015 12:41 PM
    Friday, June 19, 2015 12:43 PM

All replies

  • Hello

    tip: check firewall for 25 port


    sorry my english

    • Marked as answer by Risingflight Tuesday, June 23, 2015 12:41 PM
    Thursday, June 18, 2015 11:27 AM
  • Hi,

    Would you please post more details about your environment? For example, firewall, external mail flow and accept domain.
    How about internal or external mail flow?

    Please check the firewall port as Sneff mentioned. Then run below command to check the configuration for send connector, as well as accept domain:
    Get-SendConnector | FL
    Get-AcceptDomain | FL
    Note: pay attention to the IP range  and address space.

    Thanks


    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact tnmff@microsoft.com.

    Allen Wang
    TechNet Community Support

    • Marked as answer by Risingflight Tuesday, June 23, 2015 12:41 PM
    Friday, June 19, 2015 7:08 AM
    Moderator
  • Try to telnet to the IP over port 25.  If that fails, and it probably will based on the error message, I would first check your firewall and make sure you allow output SMTP traffic from your mail server, then I would check your ISP and make sure they don't blcok smtp traffic on port 25.

    Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread

    • Marked as answer by Risingflight Tuesday, June 23, 2015 12:41 PM
    Friday, June 19, 2015 12:43 PM
  • Thanks alot its a firewall issue
    Tuesday, June 23, 2015 12:41 PM