locked
安裝 Windows Server 2003 後 Vista 不能啟動 RRS feed

  • 問題

  • 我在我的 Windows Vista 電腦內建立了另一間隔去安裝 Windows Server 2003,
    但在安裝後就不能再啟動 Vista 了,可以如何修複呢?
    2011年6月30日 下午 01:16

解答

  • Hi,
     
    Please understand that Windows Vista uses different startup files and procedures so it is expected that the original Windows Vista system cannot be booted if you install a new dual boot Windows Server 2003 system. However, we can try the following method to make Windows Vista work again:
     
    1. Insert the Windows Vista disk into DVD-ROM.
     
    2. Click Start, click Accessories, right-click the command-prompt shortcut, and then click Run as Administrator.

    3. Type the following command at a command prompt and press Enter:

    Drive:\boot\Bootsect.exe /NT60 All

    In this command, Drive is the drive where the Windows Vista installation media is located.
     
    Note The boot folder for this step is on the DVD drive.
     
    4. type the following commands at a command prompt and press Enter.

    Note In the commands below, Drive is the drive where Windows Vista is installed.
     
    Drive:\Windows\system32\Bcdedit /create {ntldr} /d "Windows Server 2003"
     
    Drive:\Windows\system32\Bcdedit /set {ntldr} device partition=x:  (Note: x: is the drive letter for the active partition. For example, if 2003 is installed on C drive, device partition=c: )
     
    Drive:\Windows\system32\Bcdedit /set {ntldr} path \ntldr

    Drive:\Windows\system32\Bcdedit /displayorder {ntldr} /addlast

    5. Restart the computer.
     
    For more information, please refer to the following article:
    Windows Vista no longer starts after you install an earlier version of the Windows operating system in a dual-boot configuration
     
    http://support.microsoft.com/kb/919529/en-us

    thx


    Microsoft MVP for Windows Server-Networking, MCT, http://msmvps.com/blogs/richardwu
    • 已標示為解答 fattyhk 2011年6月30日 下午 01:25
    2011年6月30日 下午 01:22
    • 已標示為解答 fattyhk 2011年6月30日 下午 01:25
    2011年6月30日 下午 01:24
    版主

所有回覆

  • Hi,
     
    Please understand that Windows Vista uses different startup files and procedures so it is expected that the original Windows Vista system cannot be booted if you install a new dual boot Windows Server 2003 system. However, we can try the following method to make Windows Vista work again:
     
    1. Insert the Windows Vista disk into DVD-ROM.
     
    2. Click Start, click Accessories, right-click the command-prompt shortcut, and then click Run as Administrator.

    3. Type the following command at a command prompt and press Enter:

    Drive:\boot\Bootsect.exe /NT60 All

    In this command, Drive is the drive where the Windows Vista installation media is located.
     
    Note The boot folder for this step is on the DVD drive.
     
    4. type the following commands at a command prompt and press Enter.

    Note In the commands below, Drive is the drive where Windows Vista is installed.
     
    Drive:\Windows\system32\Bcdedit /create {ntldr} /d "Windows Server 2003"
     
    Drive:\Windows\system32\Bcdedit /set {ntldr} device partition=x:  (Note: x: is the drive letter for the active partition. For example, if 2003 is installed on C drive, device partition=c: )
     
    Drive:\Windows\system32\Bcdedit /set {ntldr} path \ntldr

    Drive:\Windows\system32\Bcdedit /displayorder {ntldr} /addlast

    5. Restart the computer.
     
    For more information, please refer to the following article:
    Windows Vista no longer starts after you install an earlier version of the Windows operating system in a dual-boot configuration
     
    http://support.microsoft.com/kb/919529/en-us

    thx


    Microsoft MVP for Windows Server-Networking, MCT, http://msmvps.com/blogs/richardwu
    • 已標示為解答 fattyhk 2011年6月30日 下午 01:25
    2011年6月30日 下午 01:22
    • 已標示為解答 fattyhk 2011年6月30日 下午 01:25
    2011年6月30日 下午 01:24
    版主
  • 謝謝你!
    2011年6月30日 下午 01:26